// FREE CALCULATOR //

5/3/1 Calculator

Enter your one-rep max, or a recent set of weight and reps, and get your 5/3/1 training max and every set of the four-week cycle: warm-ups, the three main sets and the deload, each rounded to a weight you can load.

Training max at 90%All four weeksOption one or twokg or lb
Start from
lb
Percentages
Unit

// THE CYCLE //

Four weeks, two options.

Each week has three main sets, all taken from the training max. The last set of weeks 1 to 3 is as many good reps as you can manage, short of failure.

5/3/1 percentages of the training max
WeekOption oneOption twoReps
Week 165%, 75%, 85%75%, 80%, 85%5, 5, 5+
Week 270%, 80%, 90%80%, 85%, 90%3, 3, 3+
Week 375%, 85%, 95%75%, 85%, 95%5, 3, 1+
Week 4 (deload)40%, 50%, 60%40%, 50%, 60%5, 5, 5

Start under your max

The training max is 90% of your max, so the program starts light and has room to climb. Wendler is blunt about it: if you won’t do this, don’t do the program.

Add a little each cycle

After each four-week cycle, add no more than 5 lb to the bench and press training maxes and 10 lb to the squat and deadlift (2.5 kg and 5 kg).

Warm up the same way

The manual’s warm-up is 40% for 5, 50% for 5 and 60% for 3 of the training max, then the work sets.

One inconsistency in the manual: its percentage table gives the deload week as 40%, 50% and 60%, but its worked examples load 50%, 60% and 70%. This calculator, like the IronLedger app, uses the table. 5/3/1 is Jim Wendler’s program; IronLedger is not affiliated with him.

// QUICK ANSWERS //

Common maxes, worked out.

Option one, a 90% training max, and the top set of each week.

5/3/1 training maxes and top sets for common one-rep maxes
One-rep maxTraining maxWeek 1 top setWeek 2 top setWeek 3 top set
100 kg90 kg77.5 × 5+80 × 3+85 × 1+
140 kg125 kg107.5 × 5+112.5 × 3+120 × 1+
180 kg160 kg135 × 5+145 × 3+152.5 × 1+
225 lb200 lb170 × 5+180 × 3+190 × 1+
315 lb280 lb240 × 5+255 × 3+270 × 1+
405 lb360 lb310 × 5+325 × 3+345 × 1+

// AROUND THE CYCLE //

Before and after it.

Load the bar

For the plates on each side of any of these weights, use the plate calculator.

// DIRECT ANSWERS //

Questions lifters ask.

What is the training max in 5/3/1?

The number every percentage is taken from: 90% of your one-rep max in Wendler’s manual, so you start about 10% under what you can actually lift. The manual mentions lifters starting 15% under with good results; 85% is the cautious choice here.

How do you calculate 5/3/1 weights?

Multiply your training max by each set’s percentage. With option one, week 1 is 65%, 75% and 85% for 5, 5 and 5 or more reps; week 2 is 70%, 80% and 90% for 3s; week 3 is 75%, 85% and 95% for 5, 3 and 1 or more; week 4 is a deload at 40%, 50% and 60% for 5. This calculator rounds each load to one you can put on the bar.

What is the difference between option one and option two?

Option two uses heavier first and second sets in weeks 1 and 2 (75%, 80%, 85% and 80%, 85%, 90%); weeks 3 and 4 are the same. Wendler writes that he uses option one and recommends it for almost everyone, because option two is very tiring on squat and deadlift days.

How much do I add to my training max each cycle?

No more than 5 lb on the bench press and overhead press and 10 lb on the squat and deadlift, per the manual; this calculator uses 2.5 kg and 5 kg in kilograms. Choose a lift to see the next cycle’s training max.

What do I do when I stall on 5/3/1?

The manual’s answer: when you can no longer hit the prescribed reps, take 90% of a new estimated max and work up again. Reset only the lift that stalled; if several have, take a deload week and recalculate them all.

Why does the calculator round pounds up?

Because the manual does: every load in its worked tables is the percentage rounded up to the next 5 lb. Kilogram loads round to the nearest 2.5 kg. The training max itself always rounds down to a loadable weight.

Is the 5/3/1 deload week 40/50/60 or 50/60/70?

The manual is not consistent. Its percentage table gives 40%, 50% and 60%, but its worked examples load 50%, 60% and 70%. This calculator and the IronLedger app use the table’s 40%, 50% and 60%; either way, the deload has no “or more reps” set.

Use it from an AI assistant

The same calculation is a free JSON API at /api/tools/531 and a tool on the IronLedger MCP server, so an assistant can run it and link back to this page with your numbers.

API and MCP details